IFM DP2402 Скачать руководство пользователя

Страница: 22 / 24

DP2402

Pulse stretcher

11 Troubleshooting

Display

LED

Error

Troubleshooting

Power

OFF

off

Supply voltage too low.

Check/correct the supply voltage:
Electrical connection

flashes

any

flashes

Excessive current at the switching
output OUTx (see LED I/II).

Check switching output for short
circuit or excessive current. Re-
move the fault.

C.Loc

any

Parameter setting via pushbuttons
locked due to active IO-Link trans-
mission.

Wait until parameter setting via
IO-Link is finished.

S.Loc

any

Parameter setting via pushbuttons
disabled by software.

Unlocking only possible via IO-
Link interface/IO-Link parameter
setting software.

Loc

any

Parameter setting via pushbuttons
disabled.

Unlock pushbuttons:
Locking / unlocking (

20)

Rotating seg-
ment

any

Temperature in housing exceeds
limit value.

Press any button to switch the dis-
play on for 30 s.

DEUC

any

Device identification activated (sys-
tem command: FLASH_ON)

Deactivate device identification
(system command: FLASH_OFF)

Содержание DP2402

























Результаты поиска

Содержание DP2402

Отзывы:

Похожие инструкции для DP2402

Бренды по названию

Популярные бренды

IFM DP2402, Руководство по эксплуатации

Результаты поиска

Содержание DP2402

Отзывы:

Похожие инструкции для DP2402

Бренды по названию

Популярные бренды