IFM Electronic VNB001 Скачать руководство пользователя страница 4

Страница: 4 / 27

1 Preliminary note

Technical data, approvals, accessories and further information at www�ifm�com�

1.1 Notes on this document

This document applies to devices of the type "vibration sensor" (art� no�: VNB001)�

It is part of the device and contains information about the correct handling of the

product�
This document is intended for qualified electricians� These specialists are people

who are qualified by their training and their experience to recognise and to avoid

possible hazards that may be caused during operation of the device�

►

Read this document before using the device�

►

Keep this document during the service life of the device�

1.2 Symbols used

►

Instruction

> Reaction, result

→

Cross-reference

LED on
LED flashes

Important note

Non-compliance can result in malfunction or interference�
Information

Supplementary note�

2 Safety instructions

2.1 General

►

Observe these operating instructions�

►

Observe the warning notes in these instructions�

Non-observance of the instructions, operation which is not in accordance with use

as prescribed below, wrong installation or incorrect handling can affect the safety

of operators and machinery�

2.2 Installation and connection

The unit must only be installed, connected and put into operation by a qualified

electrician as the safe function of the device and machinery is only guaranteed

Содержание VNB001




























Результаты поиска

Содержание VNB001

Отзывы:

Бренды по названию

Популярные бренды

IFM Electronic VNB001, Руководство по эксплуатации

Результаты поиска

Содержание VNB001

Отзывы:

Бренды по названию

Популярные бренды