IFM Electronic efector 300 SU9001 Скачать руководство пользователя | Manualshive

Страница: 26 / 31

background image

26

10 Operation

After power on and expiry of the power-on delay time (approx� 10 s) the unit is in

the Run mode (= normal operating mode)� It carries out its measurement and eval-

uation functions and generates output signals according to the set parameters�

• Operation indication → chapter 7 Controls and indicating elements.

•

During the power-on delay time the outputs are switched as programmed: ON

for NO function (Hno / Fno) and OFF for NC function (Hnc / Fnc)�

•

If output 2 is configured as analogue output, the output signal is at the final

value of the measuring range during the power-on delay time�

10.1 Read the set parameters

►

Press [Mode/Enter] until the requested parameter is displayed�

►

Press [Set] briefly�

> The unit displays the corresponding parameter value� After about 15 s it again

displays the parameter, then it returns to the Run mode�

10.2 Changing the display unit in the Run mode

►

Press [Set] briefly in the Run mode� Press the pushbutton to move to the next

display unit�

> The unit displays the current measured value for approx� 15 s, the correspond-

ing LED lights�

«
...
24
25
26
27
28
...
»

Содержание efector 300 SU9001
































Отзывы:

Нет отзывов

Похожие инструкции для efector 300 SU9001

POVCAM AG-HCK10G

Бренд: Gates Страницы: 2

SuperStack 3 4300

Бренд: 3Com Страницы: 8

Бренд: 3B Medical Страницы: 7

Бренд: AA Products Страницы: 8

Бренд: Danfoss Страницы: 14

Odyssey II Series

Бренд: Dakota Digital Страницы: 3

Бренд: Xsens Страницы: 53

Бренд: Viking Страницы: 5

Бренд: aquatherm Страницы: 32

Бренд: Metz Страницы: 112

Бренд: Sonero Страницы: 32

Бренд: UPPAbaby Страницы: 2

Бренд: Cognex Страницы: 39

Бренд: Cardinal Страницы: 52

Бренд: Rice Lake Страницы: 56

Бренд: RCS Страницы: 29

Бренд: ViewSonic Страницы: 2

Бренд: Keith McMillen Instruments Страницы: 89

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды