background image

 

 

                                                                   Page 

 

 

SECTION  3.0 

 

WARRANTY   INFORMATION 

 
 

Instruments For Industry, Inc.  (IFI)  warrants each product of its manufacture to be free from any 
defect in material and workmanship for a period of three years from shipment to the original 
purchaser.  All warranty returns, however, must first be authorized by our factory office 
representative.  Refer to the Service Section for information on how to return items for warranty 
repair. 
 
Warranty liability shall be limited to repair or replacement of, or part thereof, which proves to be 
defective after inspection by IFI.  This warranty shall not apply to any IFI product that has been 
disassembled, modified, physically or electrically damaged or any product that has been subjected to 
conditions exceeding the applicable specifications or ratings. 
 
IFI shall not be liable for any direct or consequential injury, loss or damage incurred through the use, 
or the inability to use, any IFI product. 
 
IFI reserves the right to make design changes to any IFI product without incurring any obligation to 
make the same changes to previously purchased units. 
 
This warranty is the full extent of obligation and liability assumed by IFI with respect to any and all 
IFI products.  IFI neither makes, nor authorizes any person to make, any other guarantee or warranty 
concerning IFI Products. 
 

Содержание S251-250







































Отзывы: