IEM Tel-O-Graph BT Скачать руководство пользователя страница 45

Страница: 45 / 54

Error messages

Communication error

Error
description

Possible cause

Remedy

Cod 1

Error during pairing

Repeat the pairing process (Chapter 7.2).

The data transfer device
is switched off

Switch the device on.

Cod 2

No Bluetooth

connection Check that the data transfer device is switched on. If this error

occurs repeatedly, contact your healthcare provider/physician.

Cod 3

Could not send readings

Take another measurement and check whether the readings
are transmitted.
If this error occurs repeatedly, contact your healthcare
provider/physician.

Cod 4

Communication error

If this error occurs repeatedly, contact your healthcare
provider/physician.

Cod 5

Invalid target data in
EEPROM (memory)

If this error occurs repeatedly, contact your healthcare
provider/physician.

Cod 6

Hardware communication
error

If this error occurs repeatedly, contact your healthcare
provider/physician.

Cod 7

Memory empty

If this error occurs repeatedly, contact your healthcare
provider/physician.

Содержание Tel-O-Graph BT























































Результаты поиска

Содержание Tel-O-Graph BT

Отзывы:

Похожие инструкции для Tel-O-Graph BT

Бренды по названию

Популярные бренды

IEM Tel-O-Graph BT, Инструкция по эксплуатации

Результаты поиска

Содержание Tel-O-Graph BT

Отзывы:

Похожие инструкции для Tel-O-Graph BT

Бренды по названию

Популярные бренды