background image

5

Base product data 

Â

A88 circuit breaker with electronic release of KARAT series of IEK 

trademark (hereinafter referred to as circuit breaker) is designed to conduct 
current in normal mode and turn off overcurrents in case of short circuits and 
overloads, as well as for infrequent (up to 30 times a day) operational switching 
on and off of electrical circuits in three-phase alternating current electrical 
networks with voltage up to 400 V and frequency of 50 Hz. 

The circuit breaker meets the requirements of Directive No. 2014/30/EU, 

2014/35/EU, IEC 60947-2.

The circuit breaker can be operated under the following conditions:
– operating temperature range from minus 25 

°

Ñ

 to plus 40 

°

Ñ

;

 

base altitude 

 no more than 1000 m, operation at the altitude of up to 

2000 m is allowed with a decrease of rated current up to 10 %;

– environment condition group according to IEC 60947-1 – A, B*;
– utilization category according to IEC 60947-2 – 

Â

 (can be used to ensure 

selectivity);

– maximum value of relative humidity – 90 % and at temperature plus 20 

°

Ñ

;

– no direct exposure to solar-radiation;
– non-explosive environment, not containing aggressive gases and vapors in 

concentrations that destroy metals and insulation, not saturated with conductive 
dust and water vapors.

The circuit breaker is intended for use in an environment with pollution 

degree 3 (conductive pollution is possible or dry, non-conductive pollution that 
becomes conductive due to expected condensation).

The circuit breaker is equipped with an electronic microprocessing release 

MP211, which provides overload protection with an inverse long tripping delay 
and an inverse time-current characteristic, and also provides short-circuit 
protection with adjustable tripping. MP211 parameters are shown in table 2.

Specifications

The technical parameters of the circuit breaker depending on the type are 

listed in table 1.

Degree of protection of the circuit breaker case is IP30, of terminals for 

connecting external conductors 

 IP00

.

ÂÀ

88 CIRCUIT BREAKERS WITH ELECTRONIC RELEASE 

EN

REAL ABILITY

When using the circuit breaker in a group B environment, special devices should be used to 

protect against unwanted electromagnetic interferences.

 

K

ARA

T

Содержание BA88-35




















Отзывы: