íåîáõîäèìûé àêñåññóàð äëÿ ñâåòîäèîäíûõ ëåíò. Ïîäêëþ÷àòü ëåíòó ê ñåòè ìîæíî òîëüêî
ïîñëå ïîëíîãî âûñûõàíèÿ ãåðìåòèêà.
Ïîäêëþ÷åíèå ëåíòû ê ñåòè 230 Â~ íåîáõîäèìî ïðîèçâîäèòü ÷åðåç äðàéâåð LED
Т
ÈÏÑÍ 500 Âò 220 Â 14 ìì RGB IP65
I
E
K
. Äëÿ ïîäêëþ÷åíèÿ ëåíòû íåîáõîäèìî:
- âñòàâèòü êîííåêòîð, èäóùèé â êîìïëåêòå ñ äðàéâåðîì, â ëåíòó. Êîííåêòîð èìååò
ðàçíóþ ôîðìó âûâîäîâ: çàîñòð¸ííûå âûâîäû ïîäêëþ÷èòü ê ëåíòå, à ñêðóãë¸ííûå
âûâîäû - ê ðàçú¸ìó äðàéâåðà (ðèñóíîê 2);
- âñòàâèòü êîííåêòîð ñ ëåíòîé â ðàçúåì äðàéâåðà â ñîîòâåòñòâèè ñ ïîëÿðíîñòüþ.
Êîíòàêòû â ðàçú¸ìå äðàéâåðà ðàñïîëîæåíû íåñèììåòðè÷íî (ðèñóíîê 2). Ïðè ìîíòàæå
ðàçú¸ì äðàéâåðà ðàñïîëîæèòü òàê, ÷òîáû êîíòàêòû ðàñïîëàãàëèñü â íèæíåé ÷àñòè
ðàçú¸ìà;
- ñìåíó öâåòîâ îñóùåñòâëÿòü êíîïêîé, ðàñïîëîæåííîé íà êîðïóñå äðàéâåðà.
- ïîäêëþ÷èòü ñåòåâîé øíóð äðàéâåðà ê ñåòè ïåðåìåííîãî òîêà 230 Â~;
EN
Basic information about the product
LED strip 5050 220 V manufactured by IEK (hereinafter-the tape) is designed to
operate from a constant voltage source 220 V.
PROHIBITED
Connect the LED strip with mechanical damage. Connect the LED strip to the
network, wound on a bobbin.
Before switching on, make sure that the voltage of the supply network matches.
Observe the polarity when connecting the tape.
The tape can be cut into sections that are multiples of one segment (1 meter). The tape
should be cut strictly according to a specially marked marking located between two adjacent
segments.
The connection of the LED strip segments should be made only using RGB connectors
Alternating voltage 230 V is life-threatening! During installation, do not expose
the tape to mechanical influences. It is not recommended to attach a tape with a
bending radius of less than 20 mm.
For the correct connection of the segments and the connection of the RGB LED strip, it is
necessary to determine the plus of the power supply "+".
The 5050 220V LED strip consists of segments, each of which has a length of 1 meter.
Each segment of the 5050 220 V tape on both sides has three contact pads marked "G", "R",
"B". The plus of the power supply "+" is located between the platforms "G" and "R" (Figure 1).
Installation of the LED strip on the support surface is carried out using a mounting bracket
Т
of 14 mm I
E
K (not included in the delivery package).
ATTENTION
Security measures
On the free end of the LED strip, to which no further connections are planned, it is
Т
necessary to install a 14 mm I
E
K end plug (not included in the delivery package).
All installation and maintenance work must be carried out in a de-energized state by
specially trained personnel in compliance with the requirements of regulatory and technical
documentation in the field of electrical engineering.
Installation and operation rules
Т
14 mm I
E
K (straight, angular or T-shaped; not included in the delivery package). The
maximum length of the tape extension depends on the power of the RGB driver or RGB
controller used with the tape. When connecting sections of the tape, observe the polarity.
2
