IEI Technology WSB-G41A-R11 Скачать руководство пользователя страница 82

Страница: 82 / 122

WSB-G41A CPU Card

Page 70



Floppy A

Use the

Floppy A

option to configure the floppy disk drive. Options are listed below:



Disabled



1.44 MB 3 1/2”

5.3.4 Super IO Configuration

Use the

Super IO Configuration

menu (

BIOS Menu 7

) to set or change the

configurations for the FDD controllers, parallel ports and serial ports.

BIOS SETUP UTILITY

Advanced

Configure ITE8718 Super IO Chipset



Parallel Port Address

[378]

Parallel Port Mode

[Normal]

Parallel Port IRQ

[IRQ7]

Serial Port1 Address

[3F8/IRQ4]

Serial Port1 Mode

[Normal]

Serial Port2 Address

[2F8/IRQ3]

Serial Port2 Mode

[Normal]



Select

Screen





Select

Item

+ -

Change Option

F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 7: Super IO Configuration



Parallel Port Address [378]

Use the

Parallel Port Address

option to select the parallel port base address.



Disabled

No base address is assigned to the Parallel Port



378 D

EFAULT

Parallel Port I/O port address is 378



278

Parallel Port I/O port address is 278



3BC

Parallel Port I/O port address is 3BC

Содержание WSB-G41A-R11



























































































































Результаты поиска

Содержание WSB-G41A-R11

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology WSB-G41A-R11, Руководство пользователя

Результаты поиска

Содержание WSB-G41A-R11

Отзывы:

Бренды по названию

Популярные бренды