IEI Technology WSB-G41A-R11 Скачать руководство пользователя страница 66

Страница: 66 / 122

WSB-G41A CPU Card

Page 54

4.6.3 USB Device Connection

There are two external USB 2.0 connectors. Both connectors are perpendicular to the

WSB-G41A. To connect a USB 2.0 or USB 1.1 device, please follow the instructions

below.

Step 1:

Located the USB connectors

. The locations of the USB connectors are shown

Chapter 4

Step 2:

Align the connectors.

Align the USB device connector with one of the

connectors on the WSB-G41A. See Figure 4-18.

Figure 4-18: USB Device Connection

Step 3:

Insert the device connector.

Once aligned, gently insert the USB device

connector into the on-board connector.

Step 0:

4.6.4 VGA Monitor Connection

The WSB-G41A has a single female DB-15 connector on the external peripheral interface

panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor

to the WSB-G41A, please follow the instructions below.

Step 1:

Locate the female DB-15 connector

. The location of the female DB-15

connector is shown in

Chapter 3

Содержание WSB-G41A-R11



























































































































Результаты поиска

Содержание WSB-G41A-R11

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology WSB-G41A-R11, Руководство пользователя

Результаты поиска

Содержание WSB-G41A-R11

Отзывы:

Бренды по названию

Популярные бренды