IEI Technology WAFER-945GSELVDS2 Скачать руководство пользователя

Страница: 78 / 140

WAFER-945GSELVDS2

Page 66

Step 5:

Insert the VGA connector

. Once the connectors are properly aligned with the

insert the male connector from the VGA screen into the female connector on the

WAFER-945GSELVDS2. See

Figure 4-20

Figure 4-20: VGA Connector

Step 6:

Secure the connector. Secure the DB-15 VGA connector from the VGA monitor

to the external interface by tightening the two retention screws on either side of

the connector.

4.10 Heat Sink Enclosure

WARNING:

Never run the WAFER-945GSELVDS2 without the heat sink secured

to the board. The heat sink ensures the system remains cool and does

not need addition heat sinks to cool the system.

Содержание WAFER-945GSELVDS2













































































































































Результаты поиска

Содержание WAFER-945GSELVDS2

Отзывы:

Похожие инструкции для WAFER-945GSELVDS2

Бренды по названию

Популярные бренды

IEI Technology WAFER-945GSELVDS2, Руководство пользователя

Результаты поиска

Содержание WAFER-945GSELVDS2

Отзывы:

Похожие инструкции для WAFER-945GSELVDS2

Бренды по названию

Популярные бренды