IEI Technology WAFER-945GSELVDS2-N270-R10 Скачать руководство пользователя страница 21

Страница: 21 / 140

WAFER-945GSELVDS2

Page 9

2.1 Anti-static Precautions

WARNING!

Failure to take ESD precautions during the installation of the

WAFER-945GSELVDS2 may result in permanent damage to the

WAFER-945GSELVDS2 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the WAFER-945GSELVDS2. Dry climates are especially susceptible to ESD. It

is therefore critical that whenever the WAFER-945GSELVDS2, or any other electrical

component is handled, the following anti-static precautions are strictly adhered to.

Wear an anti-static wristband

: - Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

Self-grounding

:- Before handling the board touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

Use an anti-static pad

: When configuring the WAFER-945GSELVDS2, place

it on an antic-static pad. This reduces the possibility of ESD damaging the

WAFER-945GSELVDS2.

Only handle the edges of the PCB

:- When handling the PCB, hold the PCB

by the edges.

2.2 Unpacking

2.2.1 Unpacking Precautions

When the WAFER-945GSELVDS2 is unpacked, please do the following:

Follow the anti-static precautions outlined in

Section 2.1

Make sure the packing box is facing upwards so the WAFER-945GSELVDS2

does not fall out of the box.

Make sure all the components shown in

Section 2.3

are present.

Содержание WAFER-945GSELVDS2-N270-R10













































































































































Результаты поиска

Содержание WAFER-945GSELVDS2-N270-R10

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology WAFER-945GSELVDS2-N270-R10, Руководство пользователя

Результаты поиска

Содержание WAFER-945GSELVDS2-N270-R10

Отзывы:

Бренды по названию

Популярные бренды