IEI Technology TANK-870AI SERIES Скачать руководство пользователя

Страница: 38 / 137

TANK-870AI Embedded System

Page 24

3.4 Wi-Fi Antenna Installation

To install the Wi-Fi antennas to the TANK-870AI series series for efficient wireless

network transmission, follow the steps below.

Step 1:

Locate the antenna connectors on the rear panel of the embedded system.

Step 2:

Install the antennas to the antenna connectors (

Figure 3-6

Figure 3-6: Wi-Fi Antenna Installation

3.5 Mounting the System with Mounting Brackets

To mount the embedded system onto a wall or some other surface using the two mounting

brackets, please follow the steps below.

Step 1:

Turn the embedded system to the left side panel.

Step 2:

Align the two retention screw holes in each bracket with the corresponding

retention screw holes on the bottom surface or the left side panel (

Figure 3-7

Содержание TANK-870AI SERIES










































































































































Результаты поиска

Содержание TANK-870AI SERIES

Отзывы:

Похожие инструкции для TANK-870AI SERIES

Бренды по названию

Популярные бренды

IEI Technology TANK-870AI SERIES, Руководство пользователя

Результаты поиска

Содержание TANK-870AI SERIES

Отзывы:

Похожие инструкции для TANK-870AI SERIES

Бренды по названию

Популярные бренды