IEI Technology TANK-870AI SERIES Скачать руководство пользователя

Страница: 111 / 137

TANK-870AI Embedded System

Page 97



Restore Defaults

Use the

Restore Defaults

option to load the optimal default values for each of the

parameters on the Setup menus.

F3 key can be used for this operation.



Save as User Defaults

Use the

Save as User Defaults

option to save the changes done so far as user defaults.



Restore User Defaults

Use the

Restore User Defaults

option to restore the user defaults to all the setup options.

5.8 Server Mgmt

Use the

Server

Mgmt

menu (BIOS Menu 29) to access the server management menus.

Server Mgmt

BMC Self Test Status

FAILED

BMC Firmware Revision

Unknown

> System Event Log
> BMC network configuration

Configure BMC network
parameters

---------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+ - Change Opt.
F1

General Help

Previous Values

Optimized Defaults

Save & Exit

ESC Exit

BIOS Menu 29: Server Mgmt

Содержание TANK-870AI SERIES










































































































































Результаты поиска

Содержание TANK-870AI SERIES

Отзывы:

Похожие инструкции для TANK-870AI SERIES

Бренды по названию

Популярные бренды

IEI Technology TANK-870AI SERIES, Руководство пользователя

Результаты поиска

Содержание TANK-870AI SERIES

Отзывы:

Похожие инструкции для TANK-870AI SERIES

Бренды по названию

Популярные бренды