IEI Technology SPCIE-C2260-i2 Скачать руководство пользователя

Страница: 73 / 162

SPCIE-C2260-i2 PICMG 1.3 CPU Card

Page 57

4.3 System Configuration

The system configuration should be performed before installation.

4.3.1 AT/ATX Power Mode Setting

The AT and ATX power mode selection is made through the AT/ATX power mode switch

which is shown in

Figure 4-7

Figure 4-7: AT/ATX Power Mode Switch Location

Setting

Description

1-2 (down)

ATX power mode (default)

2-3 (up)

AT power mode

Table 4-1: AT/ATX Power Mode Switch Settings

4.3.2 Clear CMOS Button

To reset the BIOS, remove the on-board battery and press the clear CMOS button for

three seconds or more. The clear CMOS button location is shown in

Figure 4-8

Figure 4-8: Clear CMOS Button Location

Содержание SPCIE-C2260-i2



































































































































































Результаты поиска

Содержание SPCIE-C2260-i2

Отзывы:

Похожие инструкции для SPCIE-C2260-i2

Бренды по названию

Популярные бренды

IEI Technology SPCIE-C2260-i2, Руководство пользователя

Результаты поиска

Содержание SPCIE-C2260-i2

Отзывы:

Похожие инструкции для SPCIE-C2260-i2

Бренды по названию

Популярные бренды