IEI Technology PM-BT series Скачать руководство пользователя страница 68

Страница: 68 / 108

PM-BT SBC

Page 56

5.3.1 Trusted Computing

Use the

Trusted Computing

menu (

BIOS Menu 3

) to configure settings related to the

Trusted Computing Group (TCG) Trusted Platform Module (TPM).

Advanced

Configuration

Security Device Support

[Disable]

NO Security Device Found

Enables or Disables BIOS
support for security
device. O.S. will not
show Security Device.
TCG EFI protocol and
INT1A interface will not
be available.

----------------------



: Select Screen

↑

↓

: Select Item

Enter:  Select
+/-: Change  Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 3: Trusted Computing



Security Device Support [Disable]

Use the

Security Device Support

option to configure support for the TPM.



Disable D

EFAULT

TPM support is disabled.



Enable

TPM support is enabled.

Содержание PM-BT series













































































































Результаты поиска

Содержание PM-BT series

Отзывы:

Похожие инструкции для PM-BT series

Бренды по названию

Популярные бренды

IEI Technology PM-BT series, Руководство пользователя

Результаты поиска

Содержание PM-BT series

Отзывы:

Похожие инструкции для PM-BT series

Бренды по названию

Популярные бренды