IEI Technology NANO-ULT5 Скачать руководство пользователя страница 96

Страница: 96 / 147

NANO-ULT5 SBC

Page 82

5.3.2 PCH-FW Configuration

The

PCH-FW Configuration

menu (

BIOS Menu 4

) allows Intel® Active Management

Technology (AMT) options to be configured.

Advanced

Unconfigure ME

[Disabled]

OEMFlag Bit 15:

Uncomfigure ME with

resetting MEBx password to

default.

---------------------



: Select Screen

↑

↓

: Select Item

Enter Select

F1 General Help

F2 Previous Values

Optimized Defaults

Save

ESC Exit

BIOS Menu 4: PCH-FW Configuration



Unconfigure ME [Disabled]

Use the

Unconfigure ME

option to perform ME unconfigure without password operation.



Disabled

EFAULT

Not perform ME unconfigure



Enabled

To perform ME unconfigure

Содержание NANO-ULT5




















































































































































Результаты поиска

Содержание NANO-ULT5

Отзывы:

Похожие инструкции для NANO-ULT5

Бренды по названию

Популярные бренды

IEI Technology NANO-ULT5, Руководство пользователя

Результаты поиска

Содержание NANO-ULT5

Отзывы:

Похожие инструкции для NANO-ULT5

Бренды по названию

Популярные бренды