IEI Technology NANO-ULT5 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 147

background image

NANO-ULT5 SBC

Page 96



Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard
does not become available until a USB compatible operating system is fully booted with all
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
keyboard can control the system even when there is no USB driver loaded onto the
system.



Enabled

D

EFAULT

Legacy USB support enabled



Disabled

Legacy USB support disabled



Auto

Legacy USB support disabled if no USB devices are
connected

5.3.10 CSM Configuration

Use the

CSM Configuration

BIOS Menu 16

) to configure Compatibility Support

Module (CSM).

Aptio Setup Utility – Copyright (C) 2019 American Megatrends, Inc.

Advanced

Compatibility Support Module Configuration

CSM Support

[Enabled]

Enable/Disable CSM

Support.

----------------------



: Select Screen

↑

↓

: Select Item

Enter Select

F1 General Help

F2 Previous Values

F3 Optimized Defaults

F4 Save

ESC Exit

Version 2.20.1271. Copyright (C) 2019 American Megatrends, Inc.

BIOS Menu 16: CSM Configuration

«
...
108
109
110
111
112
...
»

Содержание NANO-ULT5




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для NANO-ULT5

Бренд: Abit Страницы: 72

Бренд: PC Partner Страницы: 20

Бренд: Aaeon Страницы: 97

AP0101AT2L00XPGAH3-GEVB

Бренд: ON Semiconductor Страницы: 6

Бренд: Icop Страницы: 40

Бренд: AOpen Страницы: 8

Бренд: AXIOMTEK Страницы: 67

Бренд: Acorp Страницы: 66

Бренд: ASROCK Страницы: 56

Бренд: ASROCK Страницы: 64

A320M PRO-VH PLUS

Бренд: MSI Страницы: 154

Бренд: Intel Страницы: 1

Бренд: Gigabyte Страницы: 96

Бренд: IDT Страницы: 5

Бренд: Fujitsu Страницы: 12

ADA-91270-90340-100PFV

Бренд: Fujitsu Страницы: 24

Бренд: Fujitsu Страницы: 64

8FX MB2146-510-01-E

Бренд: Fujitsu Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды