IEI Technology KINO-KX Series Скачать руководство пользователя страница 87

Страница: 87 / 110

KINO-KX SBC

Page 75

5.4.2 South Bridge

Use the

South Bridge

menu (

BIOS Menu 21

) to configure the south bridge chipset.

Chipset

South Bridge

Auto Power Button Status

[Disabled (ATX)]

Restore AC Power Loss

[Last State]

Power Saving Function(ERP)

[Disabled]

> HDAC Configuration

Select AC power state
when power is re-applied
after a power failure.

---------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change  Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 21: South Bridge



Restore on AC Power Loss [Last State]

Use the

Restore on AC Power Loss

BIOS option to specify what state the system

returns to if there is a sudden loss of power to the system.



Power Off

The system remains turned off



Power On

The system turns on



Last State

EFAULT

The system returns to its previous state. If it was on, it

turns itself on. If it was off, it remains off.

Содержание KINO-KX Series















































































































Результаты поиска

Содержание KINO-KX Series

Отзывы:

Похожие инструкции для KINO-KX Series

Бренды по названию

Популярные бренды

IEI Technology KINO-KX Series, Руководство пользователя

Результаты поиска

Содержание KINO-KX Series

Отзывы:

Похожие инструкции для KINO-KX Series

Бренды по названию

Популярные бренды