manualshive.com logo in svg

IEI Technology KINO-KX Series, Руководство пользователя

Поделиться
Скачать
IEI Technology KINO-KX Series Скачать руководство пользователя страница 81

 

 

KINO-KX SBC 

 

Page 69 

5.3.9 USB Configuration 

Use the 

USB Configuration

  menu (

BIOS Menu 15

) to read USB configuration 

information and configure the USB settings. 

Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. 

 

Advanced 

 

 

 

 

 

 

 

USB Configuration 
 
USB Devices: 
        1 Keyboard 

 
Legacy USB Support 

[Enabled] 

 
 
 

 
Enables Legacy USB 
support. AUTO option 
disables legacy support 
if no USB devices are 
connected. DISABLE 
option will keep USB 
devices available only 
for EFI applications. 
 
--------------------- 



: Select Screen 

↑

 

↓

: Select Item 

Enter 

Select 

+/-: Change Opt. 
F1:  General Help 
F2:  Previous Values 
F3: 

Optimized 

Defaults 
F4: 

Save & Exit 

ESC:  Exit 

Version 2.20.1274. Copyright (C) 2020 American Megatrends, Inc. 

BIOS Menu 15: USB Configuration

 

 

Legacy USB Support [Enabled] 

Use the 

Legacy USB Support

  BIOS option to enable USB mouse and USB keyboard 

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard 

does not become available until a USB compatible operating system is fully booted with all 

USB drivers loaded. When this option is enabled, any attached USB mouse or USB 

keyboard can control the system even when there is no USB driver loaded onto the 

system.   

 

Enabled 

D

EFAULT

 

Legacy USB support enabled 

 

Disabled 

 

Legacy USB support disabled 

 

Auto 

 

Legacy USB support disabled if no USB devices are 

connected 

Содержание KINO-KX Series















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды