IEI Technology KINO-690S1 Скачать руководство пользователя страница 92

Страница: 92 / 229

KINO-690S1 Mini-ITX Motherboard

Page 74

Step 1:

Unlock the CPU retention screw.

When shipped, the retention screw of the

CPU socket should be in the unlocked position. If it is not in the unlocked

position, use a screwdriver to unlock the screw. See

Figure 5-1

Figure 5-1: Make sure the CPU socket retention screw is unlocked

Step 2:

Inspect the CPU socket.

Make sure there are no bent pins and make sure the

socket contacts are free of foreign material. If any debris is found, remove it with

compressed air.

Step 3:

Correctly Orientate the CPU

. Make sure the IHS (integrated heat sink) side is

facing upwards.

Step 4:

Correctly position the CPU.

Match the Pin 1 mark with the cut edge on the

CPU socket. See

Figure 5-1

Step 5:

Align the CPU pins.

Carefully align the CPU pins with the holes in the CPU

socket.

Step 6:

Insert the CPU.

Gently insert the CPU into the socket. If the CPU pins are

properly aligned, the CPU should slide into the CPU socket smoothly.

Содержание KINO-690S1






































































































































































































































Результаты поиска

Содержание KINO-690S1

Отзывы:

IEI Technology KINO-690S1, Руководство пользователя, Страница: 92 / 229

Результаты поиска

Содержание KINO-690S1

Отзывы: