IEI Technology KINO-690S1 Скачать руководство пользователя страница 50

Страница: 50 / 229

KINO-690S1 Mini-ITX Motherboard

Page 32

3.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the

KINO-690S1 may result in permanent damage to the KINO-690S1 and

severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the KINO-690S1. Dry climates are especially susceptible to ESD. It is therefore

critical that whenever the KINO-690S1, or any other electrical component is handled, the

following anti-static precautions are strictly adhered to.

Wear an anti-static wristband

: - Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

Self-grounding

:- Before handling the board touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

Use an anti-static pad

: When configuring the KINO-690S1, place it on an

antic-static pad. This reduces the possibility of ESD damaging the

KINO-690S1.

Only handle the edges of the PCB

:-: When handling the PCB, hold the PCB

by the edges.

3.2 Unpacking

3.2.1 Unpacking Precautions

When the KINO-690S1 is unpacked, please do the following:

Follow the anti-static precautions outlined in

Section 3.1

Make sure the packing box is facing upwards so the KINO-690S1 does not fall

out of the box.

Make sure all the components shown in

Section 3.3

are present.

Содержание KINO-690S1






































































































































































































































Результаты поиска

Содержание KINO-690S1

Отзывы:

IEI Technology KINO-690S1, Руководство пользователя, Страница: 50 / 229

Результаты поиска

Содержание KINO-690S1

Отзывы: