IEI Technology KINO-690S1 Скачать руководство пользователя страница 107

Страница: 107 / 229

KINO-690S1 Mini-ITX Motherboard

Page 89

To install these devices, connect the corresponding cable connector from the actual

device to the corresponding KINO-690S1 external peripheral interface connector making

sure the pins are properly aligned.

5.8.1 Audio Connection

Audio signals are interfaced through three phone jack connections. The red phone jack is

for Mic In, blue is for Line In and green is for Speaker Out. Follow the steps below to

connect audio devices to the KINO-690S1.

Step 1:

Locate the audio phone jacks

. The location of the audio phone jacks are

shown in

Chapter 3

Step 2:

Insert audio phone jack plugs

Insert audio phone jack plugs into the audio

phone jacks on the external peripheral interface. See Figure 5-14.

Step 0:

Figure 5-14: Audio Connectors

5.8.2 DVI Display Device Connection

The KINO-690S1 has a single female DVI connector on the external peripheral interface

panel. The DVI connector is connected to a digital display device. To connect a digital

display device to the KINO-690S1, please follow the instructions below.

Step 1:

Locate the DVI connector

. The location of the DVI connector is shown in

Содержание KINO-690S1






































































































































































































































Результаты поиска

Содержание KINO-690S1

Отзывы:

IEI Technology KINO-690S1, Руководство пользователя, Страница: 107 / 229

Результаты поиска

Содержание KINO-690S1

Отзывы: