IEI Technology KINO-690S1 Скачать руководство пользователя страница 103

Страница: 103 / 229

KINO-690S1 Mini-ITX Motherboard

Page 85

connectors secured on a bracket. To secure the bracket to the chassis please

refer to the reference material that came with the chassis

Step 0:

5.7.4 SATA Drive Connection

The KINO-690S1 is shipped with two SATA drive cables and one SATA drive power cable.

To connect the SATA drives to the connectors, please follow the steps below.

Step 1:

Locate the connectors

. The locations of the SATA drive connectors are shown

Chapter 3

Step 2:

Insert the cable connector

. Press the clip on the connector at the end of the

SATA cable and insert the cable connector into the onboard SATA drive

connector. See

Figure 5-10

Figure 5-10: SATA Drive Cable Connection

Step 3:

Connect the cable to the SATA disk

. Connect the connector on the other end

of the cable to the connector at the back of the SATA drive. See

Figure 5-11

Step 4:

Connect the SATA power cable

. Connect the SATA power connector to the

Содержание KINO-690S1






































































































































































































































Результаты поиска

Содержание KINO-690S1

Отзывы:

IEI Technology KINO-690S1, Руководство пользователя, Страница: 103 / 229

Результаты поиска

Содержание KINO-690S1

Отзывы: