IEI Technology IMBA-H110 Скачать руководство пользователя страница 115

Страница: 115 / 152

IMBA-H110 ATX Motherboard

Page 101

5.3.8 SATA Configuration

Use the

SATA Configuration

menu (

BIOS Menu 14

) to change and/or set the

configuration of the SATA devices installed in the system.

Advanced

SATA Controller(s)

[Enabled]

SATA Mode Selection

[AHCI]

SATA1

Empty

Hot Plug

[Disabled]

SATA2

Empty

Hot Plug

[Disabled]

SATA3

Empty

Hot Plug

[Disabled]

SATA4

Empty

Hot Plug

[Disabled]

Enable or disable SATA

Device.

---------------------



: Select Screen

↑

↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

BIOS Menu 14: SATA

Configuration



SATA Controller(s) [Enabled]

Use the

SATA Controller(s)

option to configure the SATA controller(s).



Enabled

EFAULT

Enables the on-board SATA controller(s).



Disabled

Disables the on-board SATA controller(s).



SATA Mode Selection [AHCI]

Use the

SATA Mode Selection

option to determine how the SATA devices operate.



AHCI

EFAULT

Configures SATA devices as AHCI device.



Hot Plug [Disabled]

Use the

Hot Plug

option to designate the correspondent SATA port as hot-pluggable.



Disabled

EFAULT

Disables the hot-pluggable function of the SATA port.



Enabled

Designates the SATA port as hot-pluggable.

Содержание IMBA-H110

























































































































































Результаты поиска

Содержание IMBA-H110

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology IMBA-H110, Руководство пользователя

Результаты поиска

Содержание IMBA-H110

Отзывы:

Бренды по названию

Популярные бренды