IEI Technology IMB-Q870-i2 Скачать руководство пользователя

Страница: 71 / 223

IMB-Q870-i2 microATX Motherboard

Page 55

WARNING:

The installation instructions described in this manual should be

carefully followed in order to prevent damage to the components and

injury to the user.

Before and during the installation please

the following:

Read the user manual:

The user manual provides a complete description of the IMB-Q870-i2

installation instructions and configuration options.

Wear an electrostatic discharge cuff (ESD):

Electronic components are easily damaged by ESD. Wearing an ESD cuff

removes ESD from the body and helps prevent ESD damage.

Place the IMB-Q870-i2 on an antistatic pad:

When installing or configuring the motherboard, place it on an antistatic

pad. This helps to prevent potential ESD damage.

Turn all power to the IMB-Q870-i2 off:

When working with the IMB-Q870-i2, make sure that it is disconnected

from all power supplies and that no electricity is being fed into the system.

Before and during the installation of the IMB-Q870-i2

DO NOT:

Remove any of the stickers on the PCB board. These stickers are required for

warranty validation.

Use the product before verifying all the cables and power connectors are

properly connected.

Allow screws to come in contact with the PCB circuit, connector pins, or its

components.

Содержание IMB-Q870-i2
































































































































































































































Результаты поиска

Содержание IMB-Q870-i2

Отзывы:

Похожие инструкции для IMB-Q870-i2

Бренды по названию

Популярные бренды

IEI Technology IMB-Q870-i2, Руководство пользователя

Результаты поиска

Содержание IMB-Q870-i2

Отзывы:

Похожие инструкции для IMB-Q870-i2

Бренды по названию

Популярные бренды