IEI Technology IMB-H810-i2 Скачать руководство пользователя страница 81

Страница: 81 / 215

IMB-H810-i2 microATX Motherboard

Page 65

Step 4:

Connect the SATA power cable (optional)

. Connect the SATA power

connector to the back of the SATA drive. See

Figure 4-14

Figure 4-14: SATA Power Drive Connection

The SATA power cable can be bought from IEI. See Optional Items in Section 2.4.

4.5 External Peripheral Interface Connection

This section describes connecting devices to the external connectors on the IMB-H810-i2.

4.5.1 Audio Connector

The audio jacks on the external audio connector enable the IMB-H810-i2 to be connected

to a stereo sound setup. Each jack supports both input and output. When connecting a

device, the High Definition Audio utility will automatically detect input or output. The lime

green (top) audio jack does not support input from a microphone. To install the audio

devices, follow the steps below.

Step 1:

Identify the audio plugs

. The plugs on your home theater system or speakers

may not match the colors on the rear panel.

Содержание IMB-H810-i2
























































































































































































































Результаты поиска

Содержание IMB-H810-i2

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology IMB-H810-i2, Руководство пользователя

Результаты поиска

Содержание IMB-H810-i2

Отзывы:

Бренды по названию

Популярные бренды