IEI Technology HYPER-BW Скачать руководство пользователя страница 83

Страница: 83 / 102

HYPER-BW

Page 72



Quiet Boot [Enabled]

Use the

Quiet Boot

BIOS option to select the screen display when the system boots.



Disabled

Normal POST messages displayed



Enabled

EFAULT

OEM Logo displayed instead of POST messages



UEFI Boot [Dis abled]

Use the

UEFI Boot

option to enable or disable to boot from the UEFI devices.



Auto

If the first boot HDD is GPT then enable UEFI boot
options, otherwise disable,



Enabled

Boot from UEFI devices is enabled.



Disabled

EFAULT

Boot from UEFI devices is disabled.



Launch PXE OpROM [Dis abled]

Use the

Launch PXE OpROM

option to enable or disable boot option for legacy network

devices.



Disabled

EFAULT

Ignore all PXE Option ROMs



Enabled

Load PXE Option ROMs.



Option ROM Mes s ages [Force BIOS]

Use the

Option ROM Messages

option to set the Option ROM display mode.



Force BIOS

EFAULT

Sets display mode to force BIOS.



Keep Current

Sets display mode to current.



Boot Option Priority

Use the

Boot Option Priority

function to set the system boot sequence from the available

devices. The drive sequence also depends on the boot sequence in the individual device
section.

Содержание HYPER-BW







































































































Результаты поиска

Содержание HYPER-BW

Отзывы:

Похожие инструкции для HYPER-BW

Бренды по названию

Популярные бренды

IEI Technology HYPER-BW, Руководство пользователя

Результаты поиска

Содержание HYPER-BW

Отзывы:

Похожие инструкции для HYPER-BW

Бренды по названию

Популярные бренды