IEI Technology HTB-200-C236 Скачать руководство пользователя страница 87

Страница: 87 / 113

HTB-200-C236 Embedded System

Page 75

5.4 Flash Descriptor Security Override

The flash descriptor security override jumper (J_FLASH1) allows to enable or disable the
ME firmware update. Refer to

Table 5-1

and

Figure 5-3

for the jumper location and

settings.

Setting

Description

Short 1-2

Disabled (default)

Short 2-3

Enabled

Table 5-1: Flash Descriptor Security Override Jumper Settings

Figure 5-3: Flash Descriptor Security Override Jumper Location

To update the ME firmware, please follow the steps below.

Step 1:

Before turning on the system power, short pin 2-3 of the flash descriptor security

override jumper.

Step 2:

Update the BIOS and ME firmware, and then turn off the system power.

Step 3:

Remove the metal clip on the flash descriptor security override jumper or return

to its default setting (short pin 1-2).

Step 4:

Restart the system. The system will reboot 2 ~ 3 times to complete the ME

firmware update.

Step 0:

Содержание HTB-200-C236


















































































































Результаты поиска

Содержание HTB-200-C236

Отзывы:

Похожие инструкции для HTB-200-C236

Бренды по названию

Популярные бренды

IEI Technology HTB-200-C236, Руководство пользователя

Результаты поиска

Содержание HTB-200-C236

Отзывы:

Похожие инструкции для HTB-200-C236

Бренды по названию

Популярные бренды