IEI Technology HSC-13Mx Скачать руководство пользователя страница 17

Страница: 17 / 72

HSC-13Mx Industrial Camera

Page 9

2.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the

HSC-13Mx may result in permanent damage to the camera and severe

injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the industrial camera. Dry climates are especially susceptible to ESD. It is

therefore critical that whenever the industrial camera, or any other electrical component is

handled, the following anti-static precautions are strictly adhered to.



Wear an anti-static wristband

: Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.



Self-grounding

: Before handling the board, touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.



Use an anti-static pad

: When configuring the industrial camera, place it on

an anti-static pad. This reduces the possibility of ESD damaging the industrial

camera.

2.2 Unpacking Precautions

When the industrial camera is unpacked, please do the following:



Follow the anti-static precautions outlined in

Section 2.1



Make sure the packing box is facing upwards so the industrial camera does

not fall out of the box.



Make sure all the components listed in

Section 2.3

are present.

Содержание HSC-13Mx









































































Результаты поиска

Содержание HSC-13Mx

Отзывы:

IEI Technology HSC-13Mx, Руководство пользователя, Страница: 17 / 72

Результаты поиска

Содержание HSC-13Mx

Отзывы: