IEI Technology eKINO-BT Скачать руководство пользователя

Страница: 89 / 157

eKINO-BT Mini-ITX SBC

Page 75

Figure 4-18: SATA Drive Cable Connection

Step 3:

Connect the cable to the SATA disk

. Connect the connector on the other end

of the cable to the connector at the back of the SATA drive. See

Figure 4-18

Step 4:

To remove the SATA cable from the SATA connector, press the clip on the

connector at the end of the cable.

Step 0:

4.10 External Peripheral Interface Connection

Devices can be connected to the external connectors. To install external devices, follow

the directions in the subsections below.

4.10.1 Audio Connector

The audio jacks on the external audio connector enable the eKINO-BT to be connected to

a stereo sound setup. To install the audio devices, follow the steps below.

Step 1:

Identify the audio plugs

. The plugs on your home theater system or speakers

may not match the colors on the rear panel. If audio plugs are plugged into the

wrong jacks, sound quality will be very bad.

Содержание eKINO-BT






























































































































































Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды

IEI Technology eKINO-BT, Руководство пользователя

Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды