IEI Technology eKINO-BT Скачать руководство пользователя

Страница: 88 / 157

eKINO-BT Mini-ITX SBC

Page 74

4.8 Chassis Installation

4.8.1 Airflow

WARNING:

Airflow is critical for keeping components within recommended

operating temperatures. The chassis should have fans and vents as

necessary to keep things cool.

The eKINO-BT must be installed in a chassis with ventilation holes on the sides allowing

airflow to travel through the heat sink surface. In a system with an individual power supply

unit, the cooling fan of a power supply can also help generate airflow through the board

surface.

4.8.2 Motherboard Installation

To install the eKINO-BT motherboard into the chassis please refer to the reference

material that came with the chassis.

4.9 Internal Peripheral Device Connections

This section outlines the installation of peripheral devices to the onboard connectors.

4.9.1 SATA Drive Connection

The eKINO-BT is shipped with two SATA drive cables. To connect the SATA drive to the

connector, please follow the steps below.

Step 1:

Locate the SATA connector and the SATA power connector

. The locations of

the connectors are shown in

Chapter 3

Step 2:

Insert the cable connector

. Insert the cable connector into the on-board SATA

drive connector and the SATA power connector. See

Figure 4-18

Содержание eKINO-BT






























































































































































Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды

IEI Technology eKINO-BT, Руководство пользователя

Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды