IEI Technology AFL A-N270 Series Скачать руководство пользователя страница 98

Страница: 98 / 170

AFL-xxA-N270 Series Panel PC

Page 84

Suspend Mode [S1(POS)]

Use the

Suspend Mode

BIOS option to specify the sleep state the system enters when it

is not being used.

S1 (POS) D

EFAULT

System appears off. The CPU is stopped; RAM is

refreshed; the system is running in a low power mode.

S3 (STR)

System appears off. The CPU has no power; RAM is in

slow refresh; the power supply is in a reduced power

mode.

6.3.6 APM Configuration

The

APM Configuration

menu (

BIOS Menu 10

) allows the advanced power

management options to be configured.

BIOS Menu 10: Advanced Power Management Configuration

Restore on AC Power Loss [Last State]

Use the

Restore on AC Power Loss

BIOS option to specify what state the system

returns to if there is a sudden loss of power to the system.

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Бренды по названию

Популярные бренды