IEI Technology AFL-15A-N270 Скачать руководство пользователя страница 63

Страница: 63 / 158

AFOLUX AFL-15A-N270 Panel PC

Page 63

5.1 System Maintenance Introduction

If the components of the AFL-15A-N270 series fail they must be replaced. Components

that can be replaced include:

Module

Wireless LAN module

SO-DIMM

module

Please contact the system reseller or vendor to purchase the replacement parts. Back

cover removal instructions for the AFL-15A-N270 series are described below.

5.2 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the maintenance of the

AFL-15A-N270 may result in permanent damage to the AFL-15A-N270

and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the AFL-15A-N270. Dry climates are especially susceptible to ESD. It is

therefore critical that whenever the panel PC is accessed internally, or any other electrical

component is handled, the following anti-static precautions are strictly adhered to.

Wear an anti-static wristband

: - Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

Self-grounding

: - Before handling the board touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

Use an anti-static pad

: - When configuring the AFL-15A-N270, place it on an

antic-static pad. This reduces the possibility of ESD damaging the

AFL-15A-N270.

Only handle the edges of the PCB

: - When handling the PCB, hold the PCB

by the edges.

Содержание AFL-15A-N270































































































































































Результаты поиска

Содержание AFL-15A-N270

Отзывы:

Похожие инструкции для AFL-15A-N270

Бренды по названию

Популярные бренды

IEI Technology AFL-15A-N270, Руководство пользователя

Результаты поиска

Содержание AFL-15A-N270

Отзывы:

Похожие инструкции для AFL-15A-N270

Бренды по названию

Популярные бренды