IEI Technology AFL-08AH-N270-CR Скачать руководство пользователя страница 82

Страница: 82 / 115

AFL-08AH-N270-CR Panel PC

Page 68

Serial Port Number [COM1]

Use the

Serial Port Number

option allows to select the serial port used for remote

access.

COM1 D

EFAULT

System is remotely accessed through COM1

NOTE

: Make sure the selected COM port is enabled through the Super I/O configuration

menu.

Base Address, IRQ [3F8h,4]

The

Base Address, IRQ

option cannot be configured and only shows the interrupt

address of the serial port listed above.

Serial Port Mode [115200 8,n,1]

Use the

Serial Port Mode

option to select baud rate through which the console redirection

is made. The following configuration options are available

115200

8,n,1

EFAULT

57600

8,n,1

38400

8,n,1

19200

8,n,1

09600

8,n,1

NOTE:

Identical baud rate setting musts be set on the host (a management

computer running a terminal software) and the slave

Redirection After BIOS POST [Always]

Use the

Redirection After BIOS POST

option to specify when console redirection should

occur.

Disabled

The console is not redirected after POST

Boot Loader

Redirection is active during POST and during Boot

Содержание AFL-08AH-N270-CR




















































































































Результаты поиска

Содержание AFL-08AH-N270-CR

Отзывы:

Похожие инструкции для AFL-08AH-N270-CR

Бренды по названию

Популярные бренды

IEI Technology AFL-08AH-N270-CR, Руководство пользователя

Результаты поиска

Содержание AFL-08AH-N270-CR

Отзывы:

Похожие инструкции для AFL-08AH-N270-CR

Бренды по названию

Популярные бренды