IEI Technology AFL-07A-N270/R/1G-R22 Скачать руководство пользователя страница 62

Страница: 62 / 168

AFL-xxA-N270 Series Panel PC

Page 48

Figure 4-19: Tighten the Panel Mounting Clamp Screws

4.10.3 Arm Mounting

The AFL-xxA-N270 series is VESA (Video Electronics Standards Association) compliant

and can be mounted on an arm with a 75mm or 100mm interface pad. To mount the

AFL-xxA-N270 series on an arm, please follow the steps below.

Step 1:

The arm is a separately purchased item. Please correctly mount the arm onto

the surface it uses as a base. To do this, refer to the installation documentation

that came with the mounting arm.

NOTE:

When purchasing the arm please ensure that it is VESA compliant and that

the arm has a 75 mm interface pad. If the mounting arm is not VESA

compliant it cannot be used to support the AFL-xxA-N270 series flat panel

PC. The AFL-10A-N270 and AFL-12A-N270 also support VESA MIS-D

100.

Содержание AFL-07A-N270/R/1G-R22









































































































































































Результаты поиска

Содержание AFL-07A-N270/R/1G-R22

Отзывы:

IEI Technology AFL-07A-N270/R/1G-R22, Руководство пользователя, Страница: 62 / 168

Результаты поиска

Содержание AFL-07A-N270/R/1G-R22

Отзывы: