Instruction Manual
Innovative DisplayWorks
2
SAFETY INSTRUCTIONS
To reduce the risk of fi re, electric shocks, or injury when using your cooler, please note the following basic precautions:
• Never clean appliance parts with fl ammable fl uids.
• Do not store or use gasoline or any other fl ammable vapors and liquids in the vicinity of this or any other appliance.
The fumes can cause a fi re or explosion.
• As with all electrical appliances, please consult a licensed repair technician for any repairs.
INSTALLATION
• Keep cooler in an upright position for 1-hour prior to use. This is essential for proper operation. If the cooler is
transported in the horizontal position, the cooler must be returned to the upright position and not plugged in for 1
hour.
• Remove all the packing material before using your cooler.
• Clean the interior surface with a soft cloth and lukewarm water.
• If the cooler is transported in the horizontal position, check the drain pan and ensure that it is properly positioned
above the compressor.
• For proper operation, place the cooler on a dry, level surface.
• Place the cooler at least 4” away from any walls. Otherwise, this could cause damage to the electrical cord and block
the air circulation to the appliance.
• Do not block the air intake that ventilates the condenser unit.
ELECTRIC CONNECTION
• This model operates with an 115V/60Hz power supply. Check the electrical outlet for proper voltage.
• Warning: Plug unit directly into wall outlet. Do not use an extension cord or any other multiple connectors. Do not
use an extension cord or any other multiple connectors, this could cause compressor failure.
• For your safety, plug the unit into a grounded wall outlet.
START
• Plug the cooler into the electrical outlet. For optimum performance, run cooler for 3 hours prior to use.
• Temperature Control: Do not adjust the temperature control. The temperature control is factory set to provide
maximum performance. If really necessary, you can turn the thermostat by screw driver clockwise to have lower
temperature inside the cooler
LIGHT CONTROL
• The inside light is controlled by the magnetic switch.
B
EFORE
U
SING
, P
LEASE
R
EAD
A
LL
I
NSTRUCTIONS
Innovative DisplayWorks
offi ce 909.447.8254 • fax 909.305.8756 • toll free 877.307.2665 • www.idw.global
1. Cabinet
2. Leveling Leg (4)
3. Lockpin
4. Evaporator
5. Return Pipe
6. Evaporator Fan
7. Evaporator Fan Grill
8. Evaporator Plate
9. Large Shelf
10. Shelf (2)
11. Pilasters (4)
12. Shelf Clips (12)
13. Door Gasket
14. Glass Door
15. Lock
16. Key
17. Bottom Hinge Washer
18. Bottom Hinge Board
19. Top Hinge
20. Light Cover
21. Canopy Bottom Frame
22. Fan Switch
23. Canopy Right Side
24. Fixation Board for Light
25. LED Light (4)
26. Canopy Top Frame
27. Canopy Left Side
28. Fixation of Inner Lampshade (2)
29. Interior Light Bracket
30. Top Board Bracket
31. Cabinet Top Cover
32. Compressor
33. Compressor Base
34. Power Cord
35. Thermostat Box Cover
36. Thermostat Box
37 Light Switch (G-6c: 1) (GCG-6c: 2)
38. Thermostat
39. Thermostat Label
40. Filter Drier
41. Filter Drier Bracket
42. Thermostat Box (Small)
43. Evaporator Fan Transformer
44. Power Supply Board
45. Power Supply Board Bracket
46. Transformer Box (Large)
47. Transformer
48. Power Cord Holder
49. Junction Box
50. Condenser
51. Condenser Bracket (4)
52. Connecting Pipe
53. Drip Pan
54. Drip Pan Bracket
55. Rear Grill
PARTS & IDENTIFICATION
Last Revised: July 23, 2015 1:06 PM
G-6c & GCG-6c
