IDTECK Star 100R Скачать руководство пользователя страница 23

Страница: 23 / 71

p.17

Auto-Dialer Connection (Separate purchase required)

●

Connect the other wire of Exit Button to Power GND (-) wire.

(If a normally closed Exit button is used, then see section 12-55 to change the detection

scheme from the defaulted setting)

Door Contact Sensor Connection

●

Connect Door Contact sensor (COM) wire to Door Contact Input, Yellow with Red stripe

wire.

●

Connect Door Contact sensor (NO) wire to Power GND (-) wire.

(If a normally closed Door Contact sensor is used, then see section 12-57 to change the

detection scheme from the defaulted setting.)

Auxiliary Input Device Connection (Applied to AUX In

put #1, #2, #3)

●

Connect one wire of the Auxiliary Input Device to the AUX Input wire

(Input *1 Green, Input *2 Green with White stripe, Input *3 Green with Red stripe wire).

●

Connect the other wire of Auxiliary Input Device to Power GND (-) wire.

(If a normally closed input device is used, then see section 12-49, 51 & 53 to change the

detection schemes from the defaulted settings.)

Auto-Dialer Connection (Separate purchase required)

The Auto-dialer function of this unit has not been evaluated by UL.

●

Connect the input wire of Auto-Dialer to TTL output, Orange with White stripe wire.

●

Connect (+) wire of Auto-Dialer to DC +12V (be sure that the existing power supply has

enough capacity to support this accessory or upgrade to a sufficient one.)

●

Connect (-) wire of Auto-Dialer to Power GND (-) wire.

●

Connect Telephone Line plug (RJ-14) to Auto-Dialer.

Содержание Star 100R








































































Результаты поиска

Содержание Star 100R

Отзывы:

Похожие инструкции для Star 100R

Бренды по названию

Популярные бренды

IDTECK Star 100R, Руководство пользователя

Результаты поиска

Содержание Star 100R

Отзывы:

Похожие инструкции для Star 100R

Бренды по названию

Популярные бренды