IDTECK iMDC-MAIN Скачать руководство пользователя страница 49

Страница: 49 / 79

p.43

iMDC-RIM IP ADDRESS SETTING

Sub-net Mask

Insert sub-net mask address for iMDC-MAIN board.

Gateway

Insert gateway address for iMDC-MAIN board.

DNS Server Address

Insert DNS address for iMDC-MAIN Board.

Communication Server

Insert IP address of PC installed Communication Server. Same as the one us

ed for Site Setting section.

Communication Server

Port Number

Insert port number to connect iMDC-MAIN and communication server. Def

ault is 6001.

RIM Board Port Numbe

Insert port number to connect iMDC-MAIN and iMDC-RIM Board. Default i

s 6005.

P2P(Peer to Peer) Port

Insert port number to connect iMDC-MAIN. Default is 6002.

Column Name

Description

After iMDC-MAIN setting is finished check all of settings in the first column then click th

e ‘iMDC Network Setting’ button to transmit input information to iMDC-Main.

iMDC-RIM IP ADDRESS SETTING

It’s iMDC-RIM board network information setting. All iMDC-RIMs are searched on the s

ame network and then, set Device Name, RIM Board IP address, Sub-net Mask, Gatewa

y, and DNS Address to the applicable iMDC-RIM board. Click the ‘Auto Search RIM Boar

d’ button then all of the iMDC-RIM boards connected on the same network is searched.

Select the iMDC-RIM board you want to register and move down with drag and drop. R

efer to the table below for appropriate setting.

Содержание iMDC-MAIN
















































































Результаты поиска

Содержание iMDC-MAIN

Отзывы:

Похожие инструкции для iMDC-MAIN

Бренды по названию

Популярные бренды

IDTECK iMDC-MAIN, Руководство пользователя

Результаты поиска

Содержание iMDC-MAIN

Отзывы:

Похожие инструкции для iMDC-MAIN

Бренды по названию

Популярные бренды