IDTECH ValueScan II Скачать руководство пользователя страница 5

Страница: 5 / 98

Introduction

Installation- Keyboard Wedge

Disconnect power to the terminal/computer.

Disconnect the keyboard cable from the back of the

terminal/computer and connect to the interface cable of

the scanner.

Connect the interface cable of the scanner to the

terminal/computer.

Turn the terminal/computer power on.

RS-232

Disconnect power to the terminal/computer.

Connect the external power supply (DC adapter) to the

interface cable of the scanner.

Plug the serial connector into the serial port on the back

of your computer/terminal. Tighten the two screws to

secure the connector to the port.

Plug the power pack into a power source.

Once the scanner has been fully connected, turn the

terminal/computer power back on.

USB (Simulates keyboard wedge)

1) Connect the USB cable to the terminal/computer.

2) Windows will automatically detect the USB device.

Note:

If the scanner does not operate, turn off the power

immediately and check any improper connections. Go
through all of the above steps again.

Содержание ValueScan II



































































































Результаты поиска

Содержание ValueScan II

Отзывы:

Похожие инструкции для ValueScan II

Бренды по названию

Популярные бренды

IDTECH ValueScan II, Руководство пользователя

Результаты поиска

Содержание ValueScan II

Отзывы:

Похожие инструкции для ValueScan II

Бренды по названию

Популярные бренды