IDT CPS-1848 Скачать руководство пользователя страница 111

Страница: 111 / 450

6. Event Management > Event Management Overview

CPS-1848 User Manual

111

June 2, 2014

Formal Status

This document is confidential and is subject to an NDA.

Integrated Device Technology

6.1.3

Lane Error Management Overview

Each CPS-1848 port is connected to 1, 2, or 4 lanes. Each lane can detect and report errors. Errors detected at the lane level
are indicated in the

Lane {0..47} Error Detect Register

. Information about lane events is captured if the event is enabled in the

Lane {0..47} Error Rate Enable Register

. Enabled events also contribute to the standard port error threshold events if the

IMP_SPEC_ERR bit is set in the

Port {0..17} Error Detect CSR

. Events enabled in the

Lane {0..47} Error Report Enable

can be reported to software using port-writes or interrupts, or captured in the error log, depending on the configuration

of the registers displayed in

Figure 22

Figure 22: Lane Error Management Programming Model Flow Chart

Port-writes and interrupts are disabled by default for individual Lane events.

Individual lane errors should not be enabled in the

Lane {0..47} Error Report Enable Register

because

these occur at a rate consistent with the bit error rate of each lane, and therefore are part of the normal
operation of the system.

LANE_n_ERR_RPT_EN
LANE: 0xL# * 0x100
BCST: 0x03FF10

LANE_n_CTL[LANE_INT_EN]
PORT: 0x L# * 0x100
BCST: 0xFFFF00

LANE_n_CTL[LANE_PW_EN]
PORT: 0x L# * 0x100
BCST: 0xFFFF00

PORT_n_OPS[LANE_LOG_EN]
PORT: 0x P# * 0x100
BCST: 0xF4FF04

Interrupt

Error Logging

LANE_n_ERR_RATE_EN
LANE: 0x L# * 0x100
BCST: 0xFFFF10

LANE_n_ERR_DET
LANE: 0x L# * 0x100
BCST: 0xFFFF0C

LANE_n_DATA_CAPT_0
LANE: 0x L# * 0x100
BCST: 0xFFFF10

Error Detection

Error Capture

PORT_n_ERR_RATE_CSR
0x P# * 0x40

PORT_n_ERR_RATE_THRESH_CSR
0x P# * 0x40

LANE_n_ATTR_CAPT[VALID] (!= 0)
LANE: 0x L# * 0x100
BCST: 0xFFFF14

Lane Errors

Error Capture
Valid

LANE_n_DATA_CAPT_1
LANE: 0x L# * 0x100
BCST: 0xFFFF10

Interrupts from other

Layers, Functions and Error Logging

> thresh

PORT_n_ERR_STAT_CSR
PORT: 0x P# * 0x20

Physical Layer
Implementation
Specific Errors

PORT_n_ERR_STAT_CSR
[PW_PNDG]
PORT: 0x P# * 0x20

Pending
Port Write

Содержание CPS-1848



































































































































































































































































































































































































































































Результаты поиска

Содержание CPS-1848

Отзывы:

Похожие инструкции для CPS-1848

Бренды по названию

Популярные бренды

IDT CPS-1848, Руководство пользователя

Результаты поиска

Содержание CPS-1848

Отзывы:

Похожие инструкции для CPS-1848

Бренды по названию

Популярные бренды