background image

9

©2017 Integrated Device Technology, Inc.

June 5, 2017

DISCLAIMER Integrated Device Technology, Inc. (IDT) and its affiliated companies (herein referred to as “IDT”) reserve the right to modify the products and/or specifications described herein at any time,
without notice, at IDT’s sole discretion. Performance specifications and operating parameters of the described products are determined in an independent state and are not guaranteed to perform the same
way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability
of IDT's products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not
convey any license under intellectual property rights of IDT or any third parties.

IDT's products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be rea-
sonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT.

Integrated Device Technology, IDT and the IDT logo are trademarks or registered trademarks of IDT and its subsidiaries in the United States and other countries. Other trademarks used herein are the property
of IDT or their respective third party owners. For datasheet type definitions and a glossary of common terms, visit 

www.idt.com/go/glossary

. Integrated Device Technology, Inc.. All rights reserved. 

Tech Support

www.IDT.com/go/support

Sales

1-800-345-7015 or 408-284-8200 
Fax: 408-284-2775

www.IDT.com/go/sales

Corporate Headquarters

6024 Silver Creek Valley Road 
San Jose, CA 95138 USA

www.IDT.com

8T49N24x EEPROM Programming Guide Application Note

Recovery from Incorrect Write

In case something goes wrong and the EEPROM is written incorrectly, the device may not boot correctly, and Timing Commander may be 
unable to connect to the device. If this occurs, the following steps should be used (See the User's Guide for the board revision that is 
being used):
1. Power down the evaluation board.
2. Remove the EEPROM from the socket.
3. Power up the Evaluation Board (the device will load the -998 configuration from OTP).
4. Connect to the board and use “WriteAll” to ensure the I2C communication is working correctly (steps 1–5 of 

Method 1: Direct Write to 

EEPROM Using Timing Commander and the Evaluation Board

).

5. Without powering down, place the EEPROM back in the socket.
6. Write to the EEPROM (steps 7–11 of 

Method 1: Direct Write to EEPROM Using Timing Commander and the Evaluation Board

).

7. The EEPROM should now have the correct settings programmed. 

Revision History

Revision Date

Description of Change

June 5, 2017

Added support for the 8T49N240i device

Converted the document to the latest template

August 7, 2015

Initial release. 

Содержание 8T49N24 Series










Отзывы: