IDT 89HPES16T4G2 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 149

background image

IDT Configuration Registers

PES16T4G2 User Manual

8 - 11

January 28, 2013

Notes

PCISTS - PCI Status Register (0x006)

8

SERRE

RW

0x0

SERR Enable. Non-fatal and fatal errors detected by the bridge
are reported to the Root Complex when this bit is set or the bits in
the PCI Express Device Control register are set (see PCIEDCTL -
PCI Express Device Control (0x048)).
In addition, when this bit is set it enables the forwarding of
ERR_NONFATAL and ERR_FATAL error messages from the sec-
ondary to the primary interface. ERR_COR messages are unaf-
fected by this bit and are always forwarded.
0x0 - (disable) Disable non-fatal and fatal error reporting if also

disabled in Device Control register.

0x1 - (enable) Enable non-fatal and fatal error reporting.

9

FB2B

RO

0x0

Fast Back-to-Back Enable. Not applicable.

10

INTXD

RW

0x0

INTx Disable. Controls the ability of the PCI-PCI bridge to gener-
ate an INTx interrupt message.
When this bit is set, any interrupts generated by this bridge are
negated. This may result in a change in the resolved interrupt state
of the bridge.
This bit has no effect on interrupts forwarded from the secondary to
the primary interface.

15:11

Reserved

RO

0x0

Reserved field.

Bit

Field

Field

Name

Type Default

Value

Description

2:0

Reserved

RO

0x0

Reserved field.

3

INTS

RO

0x0

INTx Status. This bit is set when an INTx interrupt is pending from
the device.
INTx emulation interrupts forwarded by switch ports from devices
downstream of the bridge are not reflected in this bit.
For downstream ports, this bit is set if an interrupt has been
“asserted” by the corresponding port’s hot-plug controller.
In the upstream port this field is always zero.

4

CAPL

RO

0x1

Capabilities List. This bit is hardwired to one to indicate that the
bridge implements an extended capability list item.

5

C66MHZ

RO

0x0

66 MHz Capable. Not applicable.

6

Reserved

RO

0x0

Reserved field.

7

FB2B

RO

0x0

Fast Back-to-Back (FB2B). Not applicable.

8

MDPED

RO

0x0

Master Data Parity Error Detected. Not applicable.

10:9

DEVT

RO

0x0

DEVSEL# TIming. Not applicable.

11

STAS

RO

0x0

Signalled Target Abort. Not applicable since a target abort is
never signalled.

12

RTAS

RO

0x0

Received Target Abort. Not applicable.

13

RMAS

RO

0x0

Received Master Abort. Not applicable.

Bit

Field

Field

Name

Type Default

Value

Description

«
...
87
88
89
90
91
...
»

Содержание 89HPES16T4G2






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 89HPES16T4G2

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 14

Бренд: Qlogic Страницы: 135

SANbox2 SANbox2-64

Бренд: Qlogic Страницы: 224

Бренд: Lindy Страницы: 70

Бренд: Technische Alternative Страницы: 4

Бренд: FCI Страницы: 78

Бренд: Steren Страницы: 13

Бренд: Articona Страницы: 2

Бренд: socomec Страницы: 38

S5130-EI Series

Бренд: H3C Страницы: 32

Бренд: YOKOGAWA Страницы: 74

Бренд: IOGear Страницы: 40

Бренд: Eaton Страницы: 3

Бренд: Epcom Страницы: 2

Clear Switch CF-POE8

Бренд: ANTIFERENCE Страницы: 7

Бренд: Comm-Tec Страницы: 40

Бренд: Grizzly Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды