background image

OPF-TH1000D/OPF-RH1000D User Guide/Command Guide 

20 

6.2.3  SFP optical transceiver 

 

Plug the attached dust cap into the SFP optical transceiver when not connecting a fiber optic cable. 

 

Do not use the attached SFP optical transceiver to other products, and do not use an SFP optical 
transceiver of other product to the OPF-H1000D. 

 

Do not use the SFP optical transceiver of the OPF-H1000D for other devices or connect fiber optical cable 
that are connected to other devices to the SFP optical transceiver of the OPF-H1000D. It may cause 
malfunctions of the SFP optical transceiver. The maximum receiving optic power used for the 
OPF-H1000D is 0 dBm. 

 

Pull the lever of the SFP optical transceiver in order to remove it. Lock the lever and push it into until it 
clicks to attach the module. 

 

Lever

RX

OP

TI

CA

L

TX

 

SFP optical transceiver 

 

6.2.4  RS-232C cable 

 

RS-232C signals (up to 115.2 Kbps) can be transmitted in duplex over a long distance. 

 

Use a cross cable or straight cable according to the connected devices. 

See: 10.1.2 RS-232C connector

 

 

 

Содержание OPF-RH1000D





















































Отзывы: