Idis DirectIP Скачать руководство пользователя страница 4

4

Safety Precautions

Do not use the product in an excessively hot (50°C or above), cold (0°C or below), or humid 
environment.

 

Presents a fire hazard.

Set up the product in a shaded area providing protection against exposure to direct sunlight 
and maintain an even ambient temperature. Do not set up the product in the vicinity of heat-
generating objects and appliances such as candles and heaters.

 

Presents a fire hazard.

There are high-voltage components inside the product. Do not attempt to open the cover or 
disassemble, repair, or modify the product.

 

Presents fire, electric shock, and physical injury hazards.

Connection ports on the rear of the product protrude out slightly, and placing the back of the 
product too close to a wall will cause the cables to bend excessively and even break. Maintain 
a distance of at least 15cm between the back of the product and the wall it faces.

 

Presents fire, electric shock, and physical injury hazards.

Do not use the product in an particularly humid, dusty, or sooty environment.

 

Presents electric shock and fire hazards.

Always keep the operating environment clean and free of dust. Use a piece of dry cloth to 
clean the product. Do not use water, thinner, or organic solvents.

 

Failure to do so can damage the product's finish and presents an electric shock hazard.

Power

Voltage fluctuation of the power supply must be within 10% of the voltage rating, and the 
power outlet must be grounded. Do not plug in electrical appliances such as a hair dryer, iron, 
and refrigerator into the same power outlet as the product.

 

Presents overheating, fire, and electric shock hazards.

Do not bend the power cable excessively or place heavy objects on top of it.

 

Presents a fire hazard.

Do not pull on the power cable or handle the power plug with wet hands. Do not insert the 
power plug into a loose power outlet.

 

Presents fire and electric shock hazards.

Product Use

Do not place a cup or container filled with a liquid on top of the product.

 

The liquid may spill over and damage the product's internals and cause a fire hazard.

Avoid dangerous situations such as placing the product or its power cable on a humid/wet 
floor, using an ungrounded extension cord, using a damaged (exposed) power cable, and 
failing to properly ground the product. Contact the retailer or a specialist if you encounter a 
problem.

 

Presents fire and electric shock hazards.

Содержание DirectIP
























Отзывы: