background image

R&D 

Access Touch 2.0 – User Manual 
Version 1.03 

Public 

8 (12) 

Author: Hal   

File:   C00320E 

Date: 

18.8.2012 

Approved: 

Jpo 

 

Printed: 

20.08.2012 

09:45

 

Idesco Oy  |  Teknologiantie 9, FIN-90590 OULU  |  Tel +358 20 743 4175  |  [email protected]  |  www.idesco.fi 

 

Picture 5: Connector 4 

5.2.5.

 

Connector 5 

Connector 5 includes two general purpose inputs. GND and +12 VDC may be connected to an exter-
nal power source. 

By default these two inputs are in “high” state. Their state reverts to “low” upon being grounded. 

Consult the separate Access Touch 2.0 Protocol Description for more information about these input 
controls. 

 

Picture 6: Connector 5 

5.2.6.

 

Ethernet Connection 

Access  Touch  2.0  possesses  one  Ethernet  connection.    This  device  supports  the  10  /  100  Mbit 
Ethernet protocol. 

Consult picture 2 to locate the Ethernet connection. 

5.2.7.

 

USB Ports 

Access Touch 2.0 has two USB ports for external USB device connections. The available USB ports 
are  located  in  the  USB1  connector.  USB2  is  reserved  for  connecting  a  touch  sensor.  USB3  is  not 
available. 

See picture 2 in chapter 5.2 for USB connection locations. 

 

 

 

Содержание Access Touch 2.0













Отзывы: