10
LF3D/LF1D LED Lighting
• Do not disassemble, repair, or modify the product. Otherwise electric
shock, fire, or malfunction may occur.
• Turn off power before wiring. Make sure that the temperature has
lowered sufficiently before wiring.
• To prevent electric shock or damage, ensure that the wiring is
correct.
• Do not stare directly into the LED while it is lit, and do not project the
light towards other people, otherwise eyes may be injured.
• The product is a general-purpose industrial electric device.
• Ensure correct operating temperature. Operating temperature is the
ambient temperature where the product will be used. Temperature
exceeding the specified value may cause rise in internal temperature
and cause damage to the unit.
• When using this product as part of or in connection with electrical
equipment for general use (*), use a DC power supply unit with a PSE
mark that conforms to the technical standards of the Product Safety
Electrical Appliance & Material (PSE). For installation, follow the laws
and regulations such as technical standards for electrical equipment
and construction equipment standards.
*
) Electrical facilities mainly for general residences and stores, receiving AC
600V or less, and small power generation facilities.
• The product is for indoor use only. Do not use outdoors, otherwise
insulation failure, electric shock, or failure may result.
• Do not use for applications which may cause harm or injury in case a
malfunction or failure occurs.
• Due to variations in LED elements, products may vary in illumination
color and illuminance.
• Before designing equipment and powering up the product, confirm
the specifications described in the instruction sheet.
• Apply voltage within the rated value, otherwise the LED elements
maybe damaged.
• Do not use or store in a location subject to vibration and shock,
otherwise electric shock or failure will result.
• Do not loosen screws, otherwise the protection characteristics will be
impaired.
• To clean the cover, use a soft cloth with water or neutral detergent.
Do not use solvents such as thinners, benzene, or alkaline, otherwise,
discoloration, deterioration, or decrease in strength may occur.
• When using this product in environments subject to dust and water,
make sure that the wiring part of cable or wire are dustproof/water-
proof. Otherwise leakage, electric shock, or failure may occur.
• Do not use in the following locations:
➀
Locations subject to high water pressure (environments exceeding protec-
tion degree IPX5, IPX7X or IPX9K in accordance with IEC 60529.)
➁
Locations subject to dust (environments exceeding protection degree IP6X
in accordance with IEC 60529.
➂
Environment subject to corrosive gases, volatile gases, flammable gases, or
chemicals that could affect the safety and reliability of the product.
➃
Locations subject to electric or magnetic fields.
➄
Subject to flammable substances.
➅
Exposed to direct sunlight, near heaters, high temperatures.
➆
Exposed to salt water.
➇
Subject to condensation or freezing, such as cold storage warehouse or air
cooler outlet (make sure that condensation or freezing do not occur).
➈
Exposed to ozone, radiation, UV or other locations where safety and reli-
ability of the product.
• When using the product as a UL/c-UL listed product, use a Class 2
power supply.
• Some metal parts are surface treated and the appearance may vary
depending on each part. Also, some scratches may appear on the
surface but does not affect product performance.
• The warranty does not apply if the product is used outside of the
conditions described in the instruction manual and specifications.
• The warranty period is one year after delivery to the specified
location.
*Exceptions to warranty coverage
The warranty period is reduced to six (6) months if the product is run
continuously over 20 hours.
• In the event of a failure caused by our responsibility within the above period,
we will replace the product free of charge at the place where the product was
purchased or delivered.
* Does not include expenses required for mounting, replacing, or installation
work.
• LED lighting have a product life.
• Because internal elements deteriorate after 8 to 10 years of installation even if they have no defects in appearance, inspection and/or replacement
are recommended. Operation condition: temperature 30°C, 3,000-hour operation per year (10 hours per day). (JIS C 8105-1)
• Product life is shortened under high operating temperature or when it is lit for long hours.
• Inspection and/or cleaning by user every 6 months is recommended.
• Inspection by contractors is recommended every 3 years.
• Do not use the product for a long time without inspection, otherwise smoke, fire, or electric shock may occur.
Safety Precautions
Instructions
Warranty
For details on mounting, wiring, and circuit examples, see the instruction manual from the
below URL.
URL
LF3D-S/F https://product.idec.com/?product=LF3D
LF3D-F1 https://product.idec.com/?product=LF3D-F1
LF3D-F2 https://product.idec.com/?product=LF3D-F2
LF3D-S/F
LF3D-F1
LF3D-F2