IDEAL LOGIC HIU Direct HT Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 32

background image

MAINTENANCE

27

LOGIC HIU

-

Installation & Servicing / Users

58 REPLACING THE DHW PRIORITY FLOW

METER

• Disconnect the flow meter cable by means of the connector.

• Extract the flow sensor (G) - Lifting upward.

• Position the new sensor.

• Reconnect the connector respecting the only possible way it

can be inserted.

59 REPLACING OR CLEANING THE DHW

PRIORITY FLOW METER TURBINE

• Isolate DHW inlet

• Extract the flow sensor

• Unscrew and remove the cartridge (H)

• Remove any impurities present or change the cartridge if

necessary and check flow turbine and saeling washer

• Screw in the cartridge

• Reposition the flow sensor and connection

When carrying out maintenance on the electrical system, for

the connections follow the diagram on p11 Indirect and p21

Direct.

After concluding maintenance, refill the system and check the

operations described in the chapter “Commissioning” and re-fit

the cover.

For information regarding spare parts or other technical

information, please contact Ideal.

Only genuine Ideal replacement components should

be used.

G

H

«
...
25
26
27
28
29
...
»

Содержание LOGIC HIU Direct HT

































Отзывы:

Нет отзывов

Похожие инструкции для LOGIC HIU Direct HT

Бренд: Radiant Страницы: 32

DOMINATOR Series

Бренд: RBI Страницы: 4

FUTERA II Series

Бренд: RBI Страницы: 4

FUTERA III Series

Бренд: RBI Страницы: 44

Ac-U-Temp ACMSS00507

Бренд: A.O. Smith Страницы: 4

Premier E-HR 24

Бренд: Atag Страницы: 32

Бренд: Crown Boiler Страницы: 56

Бренд: Olsen Страницы: 8

Бренд: Radijator Страницы: 32

Бренд: IDEAL Страницы: 6

Бренд: Ariston Страницы: 88

Бренд: Dunkirk Страницы: 40

Бренд: Dunkirk Страницы: 42

Бренд: Chaffoteaux & Maury Страницы: 12

Бренд: Aerco Страницы: 108

MINI NIKE X 24 3 E

Бренд: Immergas Страницы: 36

Бренд: Immergas Страницы: 48

Бренд: Sigma Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды