manualshive.com logo in svg

IDEAL 7228-95, Инструкция по эксплуатации

Поделиться
Скачать
IDEAL 7228-95 Скачать руководство пользователя страница 17

- 16 -

IDEAL 7228-95

05-02

08-01

25

Turning or replacing the cutting stick

- Turn the blade depth adjustment (27) to the top

until it stops (spanner in tool set).

- Remove spanner.

Danger! Risk of injury!

- Remove the cutting stick (26) with a small

screwdriver.

- Turn the cutting stick (the non-used side must be

near to the blade) and plug it into the holding bolt.
The cutting stick can be used eight times.

- Place the paper onto the whole width of the cutting

area.

- Lower the blade by pressing both cut keys. Keep

one button pressed and turn off the main switch.

- Lower the blade depth adjustment (27) until the

paper is cut along the entire length.

- Remove spanner.
- Turn main switch to position „ I „.

Cutting test

- If the last sheet of paper is not completey cut,

lower the blade adjustment (27) 1/12 using a
spanner.

- Remove spanner.
- Repeat this procedure until the paper is cut along

the entire length.

Содержание 7228-95


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды