NCV
OFF
V
Ω
V
True RMS
40
A
600
A
M
HOLD
DC
K
AC
m
Ω
V
APO
CAT.III
600V
600A
CLAMP
61-746
CAT.III
600V
V
/
Ω
COM
CORRECT
Use with
line splitter
INCORRECT
Currents
cancel
CORRECT
Single
Conductor
only
AC Voltage
DC Voltage
NCV
OFF
V
Ω
V
True RMS
40
A
600
A
M
HOLD
DC
K
AC
m
Ω
V
APO
CAT.III
600V
600A
CLAMP
61-746
CAT.III
600V
V
/
Ω
COM
OFF
40
A
600
Measuring AC Current (Amps):
CAT.III
600V
V
/
Ω
COM
NCV
OFF
V
Ω
V
True RMS
40
A
600
A
M
HOLD
DC
K
AC
m
Ω
V
APO
CAT.III
600V
600A
CLAMP
61-746
NCV
OFF
V
Ω
V
True RMS
40
A
600
A
M
HOLD
DC
K
AC
m
Ω
V
APO
CAT.III
600V
600A
CLAMP
61-746
CAT.III
600V
V
/
Ω
COM
V
Ω
V
746
Measuring Voltage:
OPERATION:
Non-contact voltage (NCV)
With the NCV tab on the tip of the clamp close to an AC voltage, press the NCV but-
ton. The NCV LED will light and the beeper will sound. The closer the NCV tab is to
AC voltage, the louder the beep. To differentiate between hot and neutral in an outlet,
insert the NCV tab into each slot in the outlet. The beeper will be much louder on
the hot side of the outlet than the neutral. The test lead can also be used to differen-
tiate between the hot and neutral. Plug the red test lead into the V/
Ω
input jack on
the meter. Press the NCV button and insert the probe tip into each slot of the outlet.
The beeper will only beep on the hot side of the outlet.
Auto/Manual Ranging Mode
( )
The meter defaults to autoranging mode when powered on. In this mode, the meter
automatically selects the best range to display the measurement. By pressing the
Range ( ) button on the meter, the manual range mode will override the auto-
ranging feature of the meter. A ( ) appears in the upper left side of the display.
Continue pressing the Range button until the desired range is obtained. Use this
mode to lock in a specific range for repeated measurements. To return to the
autoranging mode, either depress the Range button for greater than 1 second or turn
the meter off and then back on again.
Data Hold Feature
Press the Hold button on the side of the meter to toggle in and out of the data hold
mode. “HOLD” appears in the upper left of the meter display when data hold is
active. Use the data hold feature to lock a measurement reading on the display.
Press the Hold button again to unlock the display and obtain a real-time reading.
Auto Power Off (APO) Feature
The meter automatically powers itself down after about 10 minutes of no use. Press
any button, and the meter will wake up and display the last reading taken before
power down. This feature can be overridden by holding the Range ( ) button
while turning the function switch from Off to any other position. When APO is
defeated, the “APO” will be removed from the display. Turning the meter off will
restore the APO default.
H
N
NCV
OFF
V
Ω
V
True RMS
40
A
600
A
M
HOLD
DC
K
AC
m
Ω
V
APO
CAT.III
600V
600A
CLAMP
61-746
CAT.III
600V
V
/
Ω
COM
V
Ω
V
6
Page 6
Page 5
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
FAX 781.665.0780 - TestEquipmentDepot.com
