Ideal Vacuum Habanero P1012726 Скачать руководство пользователя

Страница: 18 / 19

[email protected]

www.idealvac.com

HRCF-08122022 - V 1.1

19. To change the furnace target temperature, press the

UP ARROW

. The green SV digits will

flicker.

20. Hold down the

UP ARROW

to increase the target temperature. The value will increase

slowly at first, then more quickly the longer the

UP ARROW

is depressed.

21. In Figure 20, our reference cell is Tellurium 130 and our target temperature is 650

C. When

the target is reached, press the

SET

button to save.

22. When an experiment is completed and you want to turn off the furnace but leave the controller

on, set the

r-S

value to

STOP

23. Alternatively, at the end of an experiment, turn the controller’s power switch off. The SV value

is retained and as soon as the power switch is turned back on, the furnace will immediately

begin heating if the

r-S

value is set to

RUN

Figure 20 - Set the furnace target temperature

Figure 18 - Furnace runs on powerup

5.2 WITH VARIABLE TRANSFORMER

If you are controlling the furnace with a variable transformer (Variac), make sure to use a readily

available digital temperature gauge that accepts a Type K thermocouple mini connector. Do not

run full voltage. The furnace will be damaged. Instead, increase the transformer’s voltage slowly

from zero to achieve the desired temperature.

Figure 19 - Furnace does not run on powerup

For more information about setting controller parameters, refer to the SOLO 4848 manual,

included with the controller or download the manual and RS485 serial configuration

software at

idealvac.com

Содержание Habanero P1012726




















Результаты поиска

Содержание Habanero P1012726

Отзывы:

Похожие инструкции для Habanero P1012726

Бренды по названию

Популярные бренды

Ideal Vacuum Habanero P1012726, Руководство пользователя

Результаты поиска

Содержание Habanero P1012726

Отзывы:

Похожие инструкции для Habanero P1012726

Бренды по названию

Популярные бренды